Help
Remember Me?
What's New?
Activity Stream
New Posts
New Events
Mark Forums Read
Forum
Register
Advanced Search
Home
Activity Stream
If this is your first visit, be sure to check out the
FAQ
by clicking the link above. You may have to
register
before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.
Activity Stream
Filter
Sort By
Time
Show
Recent
Recent
Popular
Popular
Anytime
Anytime
Last 7 Days
Last 7 Days
Last 30 Days
Last 30 Days
All
All
Photos
Photos
Forum
Forums
New Activity (
)
Please reload this page to view the 200+ new activity items that have been created.
Older Activity
06-22-2024,
11:58 AM
srwtlc
replied to a thread
old timers
in
ShopBotter Message Board
Possibly Gene Crain? https://www.talkshopbot.com/forum/member.php?2247-gc3
see more
2 replies | 102 view(s)
06-22-2024,
11:52 AM
ken_rychlik
replied to a thread
old timers
in
ShopBotter Message Board
I don't remember his name. Maybe Carlos, but he used to make decorative doors from what I remember.
see more
2 replies | 102 view(s)
06-22-2024,
11:37 AM
jerry_stanek
started a thread
old timers
in
ShopBotter Message Board
I was reading on another forum about a guy that was using an cnc in Mexico that was off grid do any of you remember him
see more
2 replies | 102 view(s)
06-22-2024,
08:46 AM
919RickR
replied to a thread
Help in finding bits
in
ShopBotter Message Board
Thank you Monty I will check out that bit you suggested. I run .25 bits at 2 to 2.5 IPS w/ .200 DOC Thanks again
see more
2 replies | 131 view(s)
06-21-2024,
11:21 AM
MogulTx
replied to a thread
Help in finding bits
in
ShopBotter Message Board
For an upcut, I like the Hartlauer 52-180H. Has a nice length of cut and does a great job in wood (and I cut a lot of aluminum with it too- shallow...
see more
2 replies | 131 view(s)
06-21-2024,
06:40 AM
christiangray3
started a thread
Shopbot PRT Alpha with Control Card Upgrade to run like PRS Alpha $3,500
in
For Sale/Wanted - ShopBot-related items only
For sale is a Shopbot PRT Alpha, with upgraded control cards that enable it to perform like a PRS Alpha, while maintaining the solid steel...
see more
0 replies | 102 view(s)
06-20-2024,
12:21 PM
919RickR
started a thread
Help in finding bits
in
ShopBotter Message Board
Hello all Does anyone know where I might find .250 ball nose, straight cut, and up cut carbide bits w/ 1.5 DOC that are not 6" OAL? I am machining 2...
see more
2 replies | 131 view(s)
06-19-2024,
12:01 AM
christiangray3
started a thread
Shopbot PRT Alpha with Control Card Upgrade to run like PRS Alpha $4,000
in
For Sale/Wanted - ShopBot-related items only
For sale is a Shopbot PRT Alpha, with upgraded control cards that enable it to perform like a PRS Alpha, while maintaining the solid steel...
see more
0 replies | 111 view(s)
06-17-2024,
09:57 PM
curtiss
replied to a thread
Fume/vent coverage for Shopbot
in
ShopBotter Message Board
Not sure where you are located, but I have a 30" attic fan above my table the vents into the attic. I do not use it all the time, but it...
see more
2 replies | 614 view(s)
More Activity
No More Results
No Recent Activity