PDA

View Full Version : Archives2007


  1. Broken bit woes
  2. Losing Z height during cutting
  3. Problem with Z axis - Loosing its value on JH
  4. How to contact support, etc
  5. I still have the "jitters"
  6. Stepper motors stall
  7. New 4g board issue
  8. Hold down trouble with Diamond Plate Aluminum
  9. Odd behavior today...
  10. Accuracy
  11. Problem with v26/v27 resetting speeds
  12. Rail repair
  13. New 4g install
  14. Z way too deep intermittently
  15. Bad stalling suddenly occuring...
  16. Drill axis is DOA.
  17. Run time error
  18. Reliable old file now cutting features slightly big...
  19. Programs don't keep their position
  20. Control box
  21. More broken bit woes... help!
  22. 4g upgrade and speeds?
  23. Version 3.4.2 problem
  24. Computer power
  25. Output 1 and 2 question
  26. Motor fault
  27. Run time error 5
  28. Need some expert help
  29. Semi-noob alert : Z question
  30. Keyboard Controls
  31. Odd Indexer
  32. What's happening here?
  33. 4G strange behavior
  34. ART CAM KEY
  35. Yasakawa motor and Inverter not connecting with computer
  36. Not sure if this is normal - Limit Switches
  37. Losing place.
  38. Preview Screen not opening
  39. Bit exit point
  40. GOSUB TEST_CLEAR error
  41. Broke brand new ShopBot Probe
  42. Windoze XP - What & How to turn off unneeded startup
  43. Best software?
  44. Sudden problem with my z-plate...
  45. Com port ok, but no connection to control box made
  46. PRT to PR Compatility
  47. Settings for an older PR
  48. Wrong X., Y position after compilation
  49. MDF "eating" bits
  50. Starts cutting at random spot
  51. Trouble with emergancy stop switch
  52. PC Router suddenly making noise... bushings or bearings?
  53. Loading control box SW
  54. Axis creep problem
  55. Turning off machine?
  56. Help! Please
  57. ShopBot started doing a jerking motion when turning corners
  58. Problems with small circles
  59. Problems with new ShopBot
  60. Prt alpha looses control box connection when I turn on the spindle sometimes
  61. Problem with 4g Upgrade
  62. Problem on Z axis new PRS standard
  63. They really did think of everything...
  64. 3.5.2 loose position
  65. Need help with Air Drill
  66. A first project: surfacing your table
  67. HSD Fan when does it turn on
  68. Toggle output 1
  69. Loosing Zero on all three axis
  70. Driver/motor Fault detected
  71. 4g board - Y axis only moves one direction
  72. Z and zero plate maybe
  73. Y axis just stoped
  74. Something is off .02"
  75. Z axis motor not so good (PRT 96)
  76. HELP! Shopbot Connection Problem...
  77. Prox Switch Woes
  78. Interpolating XZ orYZ
  79. Alpha losing position
  80. Can't run .sbp files created with PW3.2. new offset feature?
  81. PRS moving a 100 miles an hour
  82. Problems cutting on a vector
  83. Help Work is Stopped.
  84. Erroneous Stop Messages
  85. Feed speeds and getting them to the bot
  86. Problem with lines
  87. New Alpha Chatter
  88. Indexer Problems
  89. Systematic approad to problem solving
  90. Jog speed sluggish
  91. Misting Problem, HELP!
  92. Gantry and or bit flex...
  93. Losing X driver intermittently
  94. Z-Zero Problems
  95. Using Software to Square X Car.
  96. Resetting of Y zero in middle of job???? (HELP)
  97. Inconsistant dados
  98. PC Router not holding speed anymore...
  99. Non repeatable z=0 setting.
  100. Z Axis not functioning (newbie)
  101. #4 Input woes, crashing during a run.....
  102. Confused V carve corners not sharp?
  103. Dealing with variables
  104. Upgrading to new computer
  105. Another PR - newer computer post
  106. New Install, Wired, Turned On and BOOM!
  107. USB Not Connecting
  108. Machine output file
  109. Air drill relay switch bad?
  110. Z axis... Again
  111. Keeping sizes consistant
  112. Massive Z plunge after space bar stop
  113. Ridges?
  114. More ridges
  115. One of my y motors shuts off????
  116. Toolmarks now, where there were none,...
  117. Losing steps
  118. Port changes on me
  119. VFD-B via Modbus with DL06 PLC problem.
  120. Squareness/parallel - rails/table
  121. Toolpath Manager Library Message
  122. New Alpha Chatter (Resolved?)
  123. Losing steps - why?
  124. Adventures with USB
  125. Z-motor noise
  126. Prox Switch Problems
  127. Loss of position with deeper cuts
  128. Keypad troubles
  129. Can't get the drivers to reset after digging into a board.
  130. Corel Draw 12 to Partwizard 2
  131. Uncommanded movement at power-up
  132. Burning issues
  133. Squaring problem
  134. Area Clearance and mirrored part problems.
  135. Shopbot is double cutting and overlapping design.
  136. Not homing
  137. X axis backwards
  138. X & y axis not responding
  139. Problem with cut
  140. Hurky Jerky
  141. Loud band on ZZero
  142. Inconsistent Z heights
  143. Shopbot.ini file overwrite
  144. Lines and swirl marks on Hardwood
  145. Definition of Error Please
  146. Crooked and wandering v-carve text
  147. 7.2 upgrade, now 1 X moves faster than other...
  148. File Limit Exceeded
  149. Need PC Router Rebuild Instructions
  150. Troubles ??
  151. "path not found"
  152. Cut size not equal to part wizard-toolpath size
  153. Herky Jerky for me too...
  154. Play in motor shaft
  155. Problem with Z being perpendicular to work piece
  156. Z Zero Failure
  157. Limit switch problems, still
  158. Moving Tools Specs to new laptop
  159. What happens with Loss of Electrical Power
  160. 4g upgrade everything backwards
  161. X axis experiencing "chatter" "binding" loses position
  162. Y not responding
  163. PRSa "Z" Tune Up
  164. Gecko 202 on 4g board inop
  165. C2 = Bad file name or number (52)