PDA

View Full Version : Troubleshooting



Pages : 1 [2] 3

  1. stumbling while jogging
  2. stepper motor grind and position loss at random
  3. what is this shobot 3 popup?
  4. Z issues
  5. Hitting limit where not limit exists
  6. Shopbot workShop Ver 3xx has encounered a problem
  7. Cutting trouble
  8. VFD will not power up
  9. Shop bot OFF TRACK!!!
  10. Spindle RPM change lag
  11. Lose Z Zero during cut
  12. X Axis missing steps - Problem Solved!
  13. Possible Z Axis Issue? ~ Newbie to this!!
  14. Tab error ?
  15. Z axis motor looses lock
  16. Shopbot Desktop - DOA? Input 4 error. Help!
  17. X-axis troubles
  18. Proximity switches not reliable
  19. C3 command changes
  20. Shopbot running slower than it should.
  21. Serial Port
  22. C2 Command Problem
  23. Z Zero Setup Questions
  24. ShopBot is kinda slow today..
  25. Proximity Limits message
  26. Missing steps frustration
  27. vfd speed control
  28. router relay/4g board
  29. router fan
  30. Maintenance observations.
  31. Bot making a loud noise and sudden jolt
  32. Communication issue? Grind noise, then position loss
  33. Cannot Find Active Ports
  34. Driver Reset
  35. incorrect setup
  36. i phone remote app
  37. control software question
  38. lost my tool bar
  39. LOTS of extra moves in my cut files
  40. floating wheel
  41. shopbot present but not responding
  42. Let's Get It Lined Up!
  43. Spindle Issues.... or not???
  44. New variety of SB problems...strange ones.
  45. Shopbot Control Software question
  46. New alpha machine having problems
  47. Clean Vectors; Bad V Carve
  48. Y axis not moving
  49. Looks good in partworks, shifts on the desktop
  50. Possible Machine Cailbration
  51. Files cutting twice
  52. Error message when trying to initiate router cutting
  53. Intermittent Z-Zero issue with MTC, and Link.
  54. lost comms
  55. Present but not responding
  56. tr command
  57. Feed Rate Changes
  58. SB not finding com port
  59. Firmware question
  60. another com error
  61. com error, again.
  62. proximity sensor weirdness
  63. Schematics for PRTAlpha
  64. Cooked Circuit Board
  65. Ready to give up on HSD
  66. Missing Comm Errors and such...
  67. USB Speed Test
  68. Need help on a shuttering issue.
  69. vacuum vent pipe melting !!!!!!!!!!!!!!!
  70. Upgrade to V 3.644 Question & Such
  71. C3 problems
  72. pinion gear settings
  73. Shopbot Buddy Jerking
  74. Issue with Z changing depths in Area Clear
  75. Sub panels
  76. Missing Com Question
  77. PRTAlpha Z-Zero Plate Stopped Operating
  78. Z moves wrong direction?...
  79. Skipping Strangeness...
  80. Spindle not starting
  81. Variation on cuts from top to bottom
  82. spindle fan issue.
  83. HELP! Z depth changes as machine carves
  84. Old machine Old SW
  85. Error: Tool Stop Button On!!!
  86. SBEdit.exe error 13
  87. Lightning Strike
  88. Web Site problem for Shopbot home page?
  89. new pc displays wrong bot in setup, cant do anything.
  90. communication problems still
  91. Starting spot makes bit sized indent
  92. Help with plumbing spindle
  93. PRS Alpha JERK/BANG
  94. Old 1998 shopbot. Y axis screaming
  95. PRT Benchtop Issue
  96. Y axis cuts oval, cant snug set screws up any tighter....
  97. ShopBot Probe traveling in -Y direction?
  98. USB not conectting
  99. Retro Z UNIT VALUE settings?
  100. Shuddering after upgrade
  101. machine stops in tracks, freezes
  102. Frustrated with erratic behavior
  103. Noisy PRS Alpha
  104. Shopbot table surfacer tool
  105. Stopping cut in mid file!
  106. air drill issues
  107. X-Axis Rack warping
  108. ATC drawbar problem
  109. I am looking for help with my digitizing probe.
  110. Driver Alarm
  111. Z motor died...I think.
  112. Losing Communication
  113. false limits
  114. Partworks won't open Autocad file
  115. Shop power question
  116. My smooth isnt soo smooth..
  117. Artcam and PAF
  118. Why Why Why???
  119. S-stop, lost steps
  120. Loosing X, Y Position
  121. Rails
  122. wierd skip in cutting file
  123. Windows 8 and a new slow comm rate
  124. probe issues
  125. Yaskawa spindle won't turn on
  126. Looking for a workaround
  127. S Command, lost steps
  128. ShopBot with upgraded Control Cards. Version 3.8.02 Released 2/28/13
  129. PRT will not zero
  130. Partworks 3D and partworks tool database different
  131. Missing file
  132. Spindle Speed Ignored
  133. ok vets I need a little help!!!!!!
  134. Bought PRT Alpha, E stop issue
  135. Z-going to deep
  136. unable to reset drivers
  137. 3.8.4 My fault.
  138. proximity sensors
  139. Still No Solution...Help me please! :)
  140. 2002 PR4896 accuracy issue looking for help!!!
  141. Change Input number
  142. Wiring Diagram / Instructions Needed
  143. Error creating of writing file info log
  144. add on memory
  145. Request please..
  146. "Label finding error" hmmmm?
  147. Stuck collet (and one way to fix)
  148. Trouble in ATC setup
  149. Z gets progressively deeper
  150. not urgent
  151. SB ACTING STRANGE...HELP Please!
  152. Rod Mcdonald
  153. 12inch Z converted to18inch Z not going down all the way
  154. move and jog erratic after upgrading software need help
  155. Tool moving in wrong X direction
  156. motors
  157. Run time error 13 Type Mismatch
  158. Shifting of home position on X axis.
  159. Slow Moving Spindle in X&Y
  160. 3.8.6 Spindle turns off and loses communication solved
  161. X-Y Seems to hesitate
  162. Chattering X motors
  163. motors
  164. Confused about unit values and gear ratios
  165. Missing Comm Return????
  166. PRT zero plate wiring
  167. Port #4 Problems
  168. Z Motion Problems
  169. X-axis slow down while cutting file??
  170. Driver Alarms Flashing
  171. pause problem and symmetry problem
  172. Tool pause during cut. How to debug.
  173. Limit Switch vs XY=0,0
  174. Down is up, Up is down
  175. 7.2 unit values?
  176. stranger and strangerer
  177. Z Axis Problem
  178. did I update my shopbot with wrong machine
  179. C2 C3 problem
  180. Z axis location problem
  181. Cut Accuracy..
  182. ZZero routine issues and units
  183. New to me Shopbot PR (I think)
  184. Parts cutting too small
  185. Unfamiliar Error Message
  186. nudge
  187. Cuts are not straight, has a wiggle?
  188. Help Please! Regarding Old Shopbot (96ish cable drive)
  189. Y error
  190. Y Axis Error
  191. PRS Alpha Missing Steps
  192. straight lines being cut with a small bow.
  193. z accuracy, and low end
  194. Go to and single line
  195. Problem with my x acces
  196. preview mode no working
  197. Version 3.8.10
  198. should I upgrade to SB version 3.6.46?
  199. Strange noise and nasty vibration
  200. everything is much smaller than programmed to cut
  201. Is spindle going bad?
  202. Spindle rotation direction
  203. Surfacing problems on new BT48-12, help!
  204. Calibrating proximity switches
  205. Maxing out Z axis....
  206. Stopping Mid Probe
  207. missing post processor
  208. run time error 76 path not found
  209. What settings went wrong?
  210. Prox switch stuttering
  211. Mid-Cut Error
  212. Change Axis Direction
  213. Grinding Sound during deceleration when using "keyboard" crontrol
  214. File Load Problem
  215. Radius Corner
  216. File progress indicator problem
  217. Motor or Control board Problems?
  218. 3.8.10 - Keypad causing prox limit / z-play zeroing problems
  219. Spindle won't spin
  220. Drill doesn't spin until it touches the wood
  221. Video of what motors start doing.
  222. Dead power supply?
  223. Invalid Expression
  224. Control Box Communication Problem
  225. intermittent control box issue
  226. Z Axis Driver Problems | Gecko G202 Solution Needed
  227. Move & Jog not working properly, Move is too fast and jog is too slow!
  228. Monitor goes black with monitor logo popping up
  229. spindle speeds
  230. spark and flash
  231. Probe Error
  232. Large file issue
  233. How to conver point file to Aspire
  234. filters for usb communication cable
  235. intermittent cutting
  236. Off Center
  237. Control Box Not Connected
  238. Y-axis physical (0) incorrectly set
  239. Machine changes cut speed
  240. Y axis not moving
  241. Possible bad Driver???
  242. Version 2.38
  243. xy
  244. Problems Cutting Diagonals and Circles
  245. Alpha Spindle shutting off
  246. Deciphering the diagnostic display (UD)
  247. X-Axis is Jittery/Skipping
  248. Cutting Speeds
  249. Edges Burning
  250. Y-axis and the invisible limit