View Full Version : Mantle
srwtlc
08-04-2011, 04:39 PM
Just finished an oak leaf/acorn mantle out of cherry. Oak leaf/acorn relief from VectorArt 3D. A little Van Dyke Brown glaze under Conversion Varnish.
kartracer63
08-04-2011, 05:08 PM
Wow! That's beautiful Scott.
Brady Watson
08-04-2011, 05:36 PM
Looks good enough to eat!
-B
bleeth
08-04-2011, 06:33 PM
Scott:
Not only a great job on the mantle but I am also insanely jealous of the view outside your shop!
srwtlc
08-04-2011, 06:54 PM
I do have my share of oak leaf and acorn examples! ;)
Well done! Thank you for posting the photos.
cowboy1296
08-04-2011, 09:14 PM
beautiful. i like that glaze
Gary Campbell
08-04-2011, 09:24 PM
Nice job Scott! You should be proud.
Bring a flash drive full of pics like that to the Camp!
drandals
08-04-2011, 09:26 PM
Great lookin' mantle. How long is it?
David
myxpykalix
08-04-2011, 09:33 PM
based on the size it looks like one BIG fireplace!:eek:
great job!
srwtlc
08-04-2011, 11:02 PM
Thanks guys,
It's 85.5" long, 13" deep front to back, and 8" tall. It's meant to cover an existing old plain mantle. The oak leaves and acorns model is from VectorArt 3D. It was scaled up a little and then cut off and repeated/mirrored from the center out and a small portion was used on the ends to continue.
It's made from 4/4 cherry with a light "Ipswitch Pine" stain. Two light coats of conversion varnish (Becker Acroma Amerivar Clear Satin) and then some General Finishes Van Dyke Brown glaze (per Tim Merrill's tutorial ;) ) and then a final coat of finish.
Cutting time was approximately 30 minutes for the roughing pass with a 0.25" downcut endmill and 6 hours for the finish pass on the front with another hour each for the ends with a 0.125" tapered ballnose at 8% stepover.
I'll have to see about getting some pictures after it's in place. I'm not installing it, it's being shipped to Ohio.
MogulTx
08-05-2011, 11:48 AM
That is REALLY nice. I like it a lot. How were the 3D files priced? Expensive, reasonable, cheap? Any concern or feedback on the file(s)? I had looked at using one of those, but forget what the major concern was.
Thanks for sharing. Excellent look/work!
Monty
srwtlc
08-05-2011, 02:15 PM
Monty,
The file is from VectorArt 3D and was $50.... http://www.vectorart3d.com/store/index.cfm?Fuseaction=Detail&ID=57128 ...style A
No problem with the file. As stated earlier, I cut/copy/pasted/flipped/mirrored until I had the size as close as possible and after baking into one piece, scaled it to the final length and height without distortion.
Poogan
08-07-2011, 11:14 AM
Inspiring. What was the time invested for preparation, routing and what machines were used?
srwtlc
08-08-2011, 09:23 AM
Dan,
Material prep time wasn't much, choosing the cherry stock to use, planing to thickness with a planer, ripping and crosscutting to width and length with tablesaw and mitersaw, gluing and clamping the top together, surface sanding the top at a local cabinet shop. The thing that took the most effort, was setting up and cutting the lock miter joint on the corners at a router table. Being that the top was so long, I needed someone to support the outer end and follow along with me. Crown molding was purchased from one of the local Amish mills.
Computer time setting up the design and toolpaths took a couple of hours maybe until I was happy with it.
Cut time on the ShopBot was approximately 8 hours for all toolpaths.
About 4 hours to get the glazing done to my liking and then a couple hours in spraying the conversion varnish.
Christian
08-08-2011, 10:36 AM
Gorgeous. Nice work.
Powered by vBulletin® Version 4.2.2 Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.